1. Electronics Tools
  2. Resistor Color Code Calculator

Resistor Color Code Calculator

Tap the bands on the resistor to decode its value, tolerance and temperature coefficient — or type a value to see its colors.

4.7kΩ
1st digit: Brown2nd digit: BlackMultiplier: RedTolerance: Gold

Read from the left — the tolerance band sits apart on the right.

Band 1 of 4

1st digit

Click a band on the resistor · ← → switch band · ↑ ↓ change color

Quick picks

Resistance

1kΩ±5%

1,000 Ω

E12 standard value

How it's calculated

10×100Ω=1kΩ

Tolerance range

950Ω1kΩ1.05kΩ

Reading direction

Only reads this way: reversed, the bands aren't a valid code.

Value → color bands

Type a value in any notation — 4.7k, 4k7, 2M2, R47 or 470 — and see it on 4, 5 and 6-band resistors.

Color code reference

Tap a row to paint the 1st digit band.

ColorDigitMultiplierToleranceTemp. coeff.
Blackin use0×1Ω—250 ppm/K
Brownin use1×10Ω±1%100 ppm/K
Redin use2×100Ω±2%50 ppm/K
Orange3×1kΩ—15 ppm/K
Yellow4×10kΩ—25 ppm/K
Green5×100kΩ±0.5%20 ppm/K
Blue6×1MΩ±0.25%10 ppm/K
Violet7×10MΩ±0.1%5 ppm/K
Grey8×100MΩ±0.05%1 ppm/K
White9×1GΩ——
Goldin use—×0.1Ω±5%—
Silver—×0.01Ω±10%—

Good to know

Find the start

Gold or silver is never first. Unsure? Use Flip — the side that gives a standard value is usually right.

Standard values

Resistors come in fixed E-series steps (10, 12, 15, 18, 22, 27, 33…). A value outside them often means you read it backwards.

Power isn't in the code

The bands never tell the wattage — the body size does. Pick 1/4 W or 1/2 W from your circuit's P = I² × R.

When in doubt, measure

Faded bands blend brown, red and orange. A multimeter on Ω settles it — out of circuit, fingers off the leads.

How to read resistor color codes

Resistor bodies use colored bands to encode resistance value, tolerance, and sometimes temperature coefficient. Read digits left to right, apply the multiplier, then check the tolerance band. A 4-band resistor uses two digits, a multiplier, and tolerance; 5- and 6-band types add a third digit and optional temperature coefficient band for precision parts.

How to read a resistor color code

How the color code works

R = (significant digits) × multiplier ± tolerance

Through-hole resistors are too small to print a number on, so their value is painted as colored rings. Each color stands for a digit: black 0, brown 1, red 2, orange 3, yellow 4, green 5, blue 6, violet 7, grey 8, white 9.

On a 4-band resistor the first two bands are digits, the third is the multiplier (how many zeros to add) and the last is the tolerance. A 5-band resistor adds a third digit for precision values, and a 6-band resistor adds a final band for the temperature coefficient in ppm/K.

Gold and silver appear only as multiplier (×0.1, ×0.01) or tolerance (±5%, ±10%). That is the quickest clue to which end you should start reading from.

Worked example: yellow, violet, red, gold

A 4-band resistor from an Arduino kit shows yellow, violet, red and gold, with the gold band slightly apart from the others.

  1. Digits: yellow and violet4, 7 → 47
  2. Multiplier: red adds two zeros47 × 100 = 4 700 Ω
  3. Tolerance: gold±5% → 4 465 Ω … 4 935 Ω

The resistor is 4.7 kΩ ±5%. Any multimeter reading between 4.47 kΩ and 4.94 kΩ means the part is within spec.

Common mistakes

  • Reading from the wrong end

    A value never starts with gold or silver, and the tolerance band is usually set a little apart. Reading backwards turns 4.7 kΩ into a nonsense value or into a different real one.

  • Mixing up red, orange and brown

    Under warm or dim light these three look alike, and so do blue and violet. Check under daylight or confirm with a multimeter when in doubt.

  • Taking a brown tolerance band for a digit

    Precision 5-band parts often end in brown (±1%). Counting it as a digit shifts every band and multiplies the value by ten or more.

  • Measuring the resistor while it is in the circuit

    Other parts in parallel pull the reading down. Lift one leg of the resistor before you measure it.

Resistor color code FAQ

Start from the end where the bands are bunched together. The gold or silver tolerance band sits on the other side, often with a wider gap. If both ends look the same, try both readings: only one usually gives a standard E12 or E24 value.

A 4-band resistor has two digits, a multiplier and a tolerance, which is typical for ±5% carbon film parts. A 5-band resistor has three digits for ±1% or better metal film parts. A 6-band resistor adds a temperature coefficient band, for example brown for 100 ppm/K.

As the last band, gold means a tolerance of ±5%. In the multiplier position it means ×0.1, so green, blue, gold reads 5.6 Ω.

The tolerance band allows for it: a ±5% 1 kΩ resistor can measure anywhere from 950 Ω to 1 050 Ω. Test-lead resistance matters below about 10 Ω, and measuring in-circuit adds parallel paths.

It is a zero-ohm link: a jumper shaped like a resistor so pick-and-place and bending machines can fit it like any other part.

Values follow the E-series. E12 has twelve steps per decade (10, 12, 15, 18, 22, 27, 33, 39, 47, 56, 68, 82) spaced so that, with ±10% tolerance, every value in the decade is covered by some part.

Free shipping

On orders over 5000DA

Easy returns

7-day hassle-free returns

Fast checkout

payments on delivery and fast shipping

24/7 support

We're here to help

Dzduino Online Store

Eempowering engineers, students, makers, researchers, and businesses with high-quality and innovative technical solutions.

  • Sales: store@dzduino.com
  • Store: +213 550 88 88 27
  • Sales: +213 550 88 88 29
  • Support: +213 550 88 88 37
  • 043 Cite Remila (Route du Port), Tigditt - Mostaganem

Shop

  • All Categories
  • Électronique & Développement
  • Tools & Equipements & DIY
  • Téléphonie & Communication
  • Fabrication & Prototyping
  • Computers & Networks
  • Power & Energy & Solar
  • Video Surveillance & Security systems
  • Educational, Scientific and Laboratory

Support

  • Track order
  • Orders
  • Account
  • Shipping & returns
  • Shipping calculator

Company

  • About
  • Contact us
  • Site map
  • Privacy
  • Terms

Stay in the loop

New stock, maker deals, and electronics tips — straight to your inbox.

© 2026 Dzduino Electronics, All Rights Reserved

TermsPrivacyShipping & returnsSite map
CIBBARIDI MobFawriPayCash

Related products

Boards, modules, and kits that pair with this tool.

View all
Resistor 1/4W
DZD0000727072

Resistor 1/4W

FromDZD 5.00In StockIn Stock
LED  3mm,  Red, Green, Yellow, Blue, White
DZD0001352189

LED 3mm, Red, Green, Yellow, Blue, White

DZD 5.00In StockIn Stock
74LSxx TTL Logic
DZD000136246

74LSxx TTL Logic

FromDZD 5.00In StockIn Stock
Electrolytic Capacitor
DZD000137334

Electrolytic Capacitor

FromDZD 5.00In StockIn Stock
Gang socket outlet 16A
DZD0001750

Gang socket outlet 16A

DZD 600.00Out of StockOut of Stock
30*30*25mm Heatsink for TO-220
DZD00020930

30*30*25mm Heatsink for TO-220

DZD 60.00In StockIn Stock
4 X 3 Matrix Keypad
DZD0002174

4 X 3 Matrix Keypad

DZD 900.00In StockIn Stock
Transistors - NPN BC547
DZD000221279

Transistors - NPN BC547

DZD 30.00In StockIn Stock
Free express shipping on orders over 10,000DA
SpecialSaleBlogPrint & CutLabContact usToolsNewLabNew