1. Electronics Tools
  2. RC Filter Calculator

RC Filter Calculator

Give two of R, C and the cut-off frequency to get the third — then watch the frequency response and what the filter does to a real signal.

−3 dB
Try

Calculate

Ω
F
Hz

e.g. 50 Hz mains hum, 490 Hz Arduino PWM: see how much of it gets through.

Frequency response

1 Hz10 Hz100 Hz1 kHz10 kHz100 kHz0 dB-10 dB-20 dB-30 dB-40 dB0°−45°−90°fc 159.2 Hz · −3 dB– – phase
VinVout10 kΩ100 nFIN: slow + fast toneOUT

The input mixes a slow tone (fc ÷ 3) and a fast one (3 × fc): after the low-pass, the fast ripple is mostly gone.

Cut-off frequency

159.2Hz

Signals above 159.2 Hz are attenuated, 20 dB more every ×10 in frequency.

R 10 kΩC 100 nF

Results

Time constant τ
1 ms
Settles (5 τ)
5 ms
Slope per decade
−20 dB
Phase at fc
−45°

Sensible values: easy to drive, low noise, standard parts.

Step by step

  1. fc

    fc = 1 / (2π × R × C)

    = 1 ÷ (2π × 10 kΩ × 100 nF) = 159.2 Hz

  2. τ

    τ = R × C

    = 10 kΩ × 100 nF = 1 ms

Good to know

−20 dB per decade

One RC stage cuts 20 dB (×10) each time the frequency goes ×10 past fc. Two stages give −40 dB/decade.

Mind what's after it

The next stage's input resistance sits in parallel with the filter. Keep it 10× above R, or buffer with an op-amp.

PWM to analog

For Arduino PWM (490 Hz), put fc around 5–10 Hz: ripple drops, but the output takes 5 τ to follow changes.

Time vs frequency

τ = R × C. After one τ the output has moved 63 %, after 5 τ it's within 1 %. Lower fc means slower response.

How an RC filter works

A capacitor's impedance falls as frequency rises. In a low-pass, R feeds C: slow signals reach the output, fast ones are shorted to ground by C. Swap them for a high-pass. The cut-off fc = 1 / (2πRC) is where the output has fallen to 70.7 % (−3 dB) and lags by 45°.

How an RC filter works

How the cut-off frequency is calculated

fc = 1 / (2π × R × C)

A resistor and a capacitor form the simplest filter. In a low-pass filter the signal goes through R and C sits to ground: slow signals pass, fast ones are shorted by the capacitor. Swap them (C in series, R to ground) and you get a high-pass filter that blocks DC and slow drifts.

At the cut-off frequency fc the output is down to 70.7% of the input (−3 dB) and shifted by 45°. Beyond it a first-order filter falls by 20 dB per decade: ten times past fc, only about a tenth of the signal remains.

The time constant τ = R × C describes the same filter in time: after a step, the low-pass output reaches 63% of its final value after 1 τ and about 99% after 5 τ.

Worked example: smoothing a sensor with 10 kΩ and 100 nF

You put a 10 kΩ resistor and a 100 nF capacitor in front of an analog input as a low-pass filter.

  1. Cut-off frequencyfc = 1 / (2π × 10 000 × 100 × 10⁻⁹) ≈ 159 Hz
  2. Time constantτ = 10 000 × 100 × 10⁻⁹ = 1 ms
  3. Attenuation ten times higher (1.6 kHz)20 × log₁₀(1 / √(1 + 10²)) ≈ −20 dB

The filter passes the slow sensor signal, cuts noise above about 159 Hz, and settles within about 5 ms after a change.

Common mistakes

  • Forgetting the 2π

    1 / (R × C) gives the angular frequency in rad/s, about 6.3 times larger than fc in hertz.

  • Mixing up nF and µF

    100 nF is 0.1 µF. A factor of 1 000 on C moves the cut-off by a factor of 1 000 too.

  • Ignoring the load

    Whatever follows the filter sits in parallel with it. A load that is not much larger than R (ten times or more) shifts the cut-off and lowers the output, so buffer it if needed.

  • Expecting a sharp cut

    A single RC stage only falls by 20 dB per decade. For steeper filtering, cascade stages (with a buffer between them) or use an active filter.

RC filter FAQ

fc = 1 / (2π × R × C), with R in ohms, C in farads and fc in hertz. For 1 kΩ and 1 µF: fc ≈ 159 Hz.

Same parts, different order. Low-pass: R in series, C to ground, keeps slow signals and removes noise. High-pass: C in series, R to ground, removes DC and slow drifts and keeps fast changes.

Choose one, usually R between 1 kΩ and 100 kΩ, then compute C = 1 / (2π × R × fc) and take the nearest standard value. For 1 kHz with 3.3 kΩ: C ≈ 48 nF, so 47 nF gives about 1.03 kHz.

The output voltage is 1/√2, about 70.7% of the input, so half the power. It is the conventional edge of the filter's passband.

Yes. The Uno's PWM runs at about 490 Hz; a filter at around 10 Hz to 50 Hz (for example 10 kΩ and 1 µF, fc ≈ 16 Hz) turns it into a fairly steady DC voltage, with some ripple left.

Free shipping

On orders over 5000DA

Easy returns

7-day hassle-free returns

Fast checkout

payments on delivery and fast shipping

24/7 support

We're here to help

Dzduino Online Store

Eempowering engineers, students, makers, researchers, and businesses with high-quality and innovative technical solutions.

  • Sales: store@dzduino.com
  • Store: +213 550 88 88 27
  • Sales: +213 550 88 88 29
  • Support: +213 550 88 88 37
  • 043 Cite Remila (Route du Port), Tigditt - Mostaganem

Shop

  • All Categories
  • Électronique & Développement
  • Tools & Equipements & DIY
  • Téléphonie & Communication
  • Fabrication & Prototyping
  • Computers & Networks
  • Power & Energy & Solar
  • Video Surveillance & Security systems
  • Educational, Scientific and Laboratory

Support

  • Track order
  • Orders
  • Account
  • Shipping & returns
  • Shipping calculator

Company

  • About
  • Contact us
  • Site map
  • Privacy
  • Terms

Stay in the loop

New stock, maker deals, and electronics tips — straight to your inbox.

© 2026 Dzduino Electronics, All Rights Reserved

TermsPrivacyShipping & returnsSite map
CIBBARIDI MobFawriPayCash

Related products

Boards, modules, and kits that pair with this tool.

View all
Resistor 1/4W
DZD0000727072

Resistor 1/4W

FromDZD 5.00In StockIn Stock
LED  3mm,  Red, Green, Yellow, Blue, White
DZD0001352189

LED 3mm, Red, Green, Yellow, Blue, White

DZD 5.00In StockIn Stock
74LSxx TTL Logic
DZD000136246

74LSxx TTL Logic

FromDZD 5.00In StockIn Stock
Electrolytic Capacitor
DZD000137334

Electrolytic Capacitor

FromDZD 5.00In StockIn Stock
Gang socket outlet 16A
DZD0001750

Gang socket outlet 16A

DZD 600.00Out of StockOut of Stock
30*30*25mm Heatsink for TO-220
DZD00020930

30*30*25mm Heatsink for TO-220

DZD 60.00In StockIn Stock
4 X 3 Matrix Keypad
DZD0002174

4 X 3 Matrix Keypad

DZD 900.00In StockIn Stock
Transistors - NPN BC547
DZD000221279

Transistors - NPN BC547

DZD 30.00In StockIn Stock
Free express shipping on orders over 10,000DA
SpecialSaleBlogPrint & CutLabContact usToolsNewLabNew